Manual.ly Logo

Krups EA8170 Arabica Display Bedienungsanleitung

0,0 · 0 Bewertungen

PDF-Handbuch · 74 Seiten

Deutsch

M: QW-35-FL
Seite

/ 74

Loading...
7bc8af95ffe4a88f6dd7a70041aa269ac001 page f
25
24
■A screen indicates that the appliance is heating up. Once the appliance has finished heating up, you can begin to
make steam by pressing START
, and following these steps (13):
Step 1: holding the milk jug in place, insert the steam nozzle approximately 2 cm into the milk and wait for it to
start frothing.
Step 2: raise the container slightly (approximately 1 cm). Do not completely submerge the metal tube.
Step 3: gradually lower the container as the froth accumulates. (14)
■When you have frothed the milk enough, press the STOP button
to stop the cycle. Warning: the cycle does not
stop immediately.
■To remove any milk traces from the steam nozzle, place a container under the nozzle and start the steam function
again (approximately 10 seconds).
■The steam nozzle is removable in order to allow for deep cleaning. Wash it with water and a little non-abrasive
detergent using a brush. Rinse and dry (15-16). Before replacing, make sure that the air holes are not clogged with
milk residue. Unclog the holes with the needle supplied with your appliance if necessary (17).
■To stop the steam, press the STOP button
.
WARNING: THE CYCLE DOES NOT STOP IMMEDIATELY.
Steam can be produced for a maximum of 2 minutes per cycle.
Auto-cappuccino XS 6000 set (sold separately)
■This auto-cappuccino accessory enables you to make cappuccinos or lattes (18). Connect the different parts to
each other. Ensure that the pipe is not pierced by keeping the knob in the correct place.
■After removing the lid, fill the jug with milk (19) and place a cup or glass under the auto-cappuccino nozzle (20).
Select cappuccino or latte on the special nozzle (21).
■Start steam, as indicated in the chapter Making drinks with steam.
■Once you have made the milk froth, place your cup under the coffee jets and start a coffee cycle (22).
To prevent the milk from drying on the auto-cappuccino accessory, ensure that you clean it thoroughly. You are advised
to wash it immediately by running a steam cycle with the accessory jug filled with water in order to clean the inside
of the nozzle. For this you can use the KRUPS liquid detergent available separately.
Emptying the coffee grounds collector and the drip tray
■If the
symbol starts flashing, empty and clean the drip tray (the drip tray may contain coffee grains) and the coffee
grounds collector (23-25).
■The drip tray is fitted with floats which indicate when it needs to be emptied (26). Once you have removed the coffee
grounds collector, you should empty it completely in order to avoid any overflow.
■The warning message will continue to be displayed if the coffee grounds collector is not pushed in or inserted
correctly (24). You cannot make an espresso or a coffee while the warning message is shown.
Rinsing the circuits :
Press the maintenance and settings button
(27). The function indicator is shown above the maintenance button
.
If necessary, using the navigation button,
select the rinse symbol .
Press START , rinsing starts and finishes when the coffee menu appears.
MAINTAINING YOUR APPLIANCE
Preparing the grinder
You can adjust the strength of your coffee by adjusting how finely the coffee beans are ground.
Generally, the finer the coffee is ground, the stronger and creamier the coffee will be, but this also depends on the
type of coffee used.
Adjust the fineness of grinding by turning the coffee grounds fineness adjustment knob
which is located in the
coffee bean container. It is advised that you do this during grinding, one notch at a time.
After 3 rounds, you will notice a pronounced difference in taste. To the left, the grounds are finer. To the right, the
grounds are courser. (7)
Claris F 088 - Aqua Filter System cartridge (Sold separately)
To optimise the taste of your drinks and the lifespan of your appliance, you are advised to only use a Claris - Aqua
Filter System cartridge with your machine (see the chapter OTHER FUNCTIONS – Installing the filter).
Every time you place a Claris-Aqua Filter into the machine you must prime the filter before using the machine by
activating the “install filter cartridge” program.
Note :
The amount of water for making an espresso is between 30 and 70 ml.
The amount of water for making a coffee is between 80 and 180 ml.
Starting preparation (with 1 or 2 cups)
■Press the on-off button
, and wait for the appliance to finish heating up.
■The coffee types menu is displayed. The function indicator is shown above the coffee types button (6).
■Place one or two cups under the coffee jets. You can lower or raise the coffee jets according to the size of your cup
(8). Select the coffee strength (shown coffee beans displayed on the screen in brackets) with the + button to
increase or the - button to decrease. (9).
■Press the navigation button to set the volume: select the volume of water displayed on the screen between
brackets using the + or - buttons (10).
■Press the navigation button
to set the number of cups: select 1 or 2 cups, displayed on the screen between
brackets using the + or - buttons
.
■Press the START button
(11).
■You can set the water volume at any time using the + or - buttons .
■To stop the flow into your cup, press the STOP button
.
■You can also adjust the temperature of your coffee (see the chapter OTHER functions - Settings).
Two cup function
The appliance will automatically carry out 2 full cycles of coffee preparation.
MAKING AN ESPRESSO AND A COFFEE
Steam is used to froth the milk, for example when preparing a cappuccino or caffe latte, and also to heat up liquids.
As a higher temperature is required when producing steam than when making an espresso, the appliance will launch
an additional pre-heating phase.
Frothing milk
■For best results, you are advised to use very fresh, very cold pasteurised or UHT milk, recently opened. Unpasteurised
milk does not produce the best results.
■Check that the steam nozzle is correctly positioned.
■Pour the milk into a milk jug which has a handle or into a cappuccino cup. Only fill it half way.
■When the screen displays the drink selection menu, press the steam button
(12). The function indicator is
located above the steam button
.
■Insert the steam nozzle into the milk.
MAKING DRINKS USING STEAM

Chatten Sie mit Ihrem Krups EA8170 Arabica Display-Handbuch mithilfe von KI

Erhalten Sie sofortige KI-Antworten aus Ihrem Krups EA8170 Arabica Display-Handbuch

Fragen Sie alles über Krups EA8170 Arabica Display. Antworten stammen aus diesem Handbuch, mit den Seiten, auf denen sie basieren.

EA8170 Arabica Display Wartungsplan

Erinnere mich, wenn eine Wartung faellig ist
Alle 2 Monate
Kartusche des Claris Aqua Filtersystems ersetzen

Die Kartusche verfugt uber einen Datumsmechanismus, der den Austausch nach maximal 2 Monaten anzeigt, um optimalen Geschmack und eine lange Lebensdauer des Gerats sicherzustellen.

Bei Aufforderung durch das Gerat
Automatisches Reinigungsprogramm mit KRUPS Tablette ausfuhren

Legen Sie die KRUPS Reinigungstablette in den Einfulltrichter. Fullen Sie den Wassertank bis zur maximalen Fullmenge. Stellen Sie einen Behalter mit 0,6 L Fassungsvermögen unter die Auslaufe und starten Sie den Zyklus.

Bei Aufforderung durch das Gerat
Entkalkungsprogramm mit KRUPS Beutel ausfuhren

Entfernen Sie die Filterkartusche, falls installiert. Geben Sie einen Beutel KRUPS Entkalker in den Wassertank bis zur Markierung CALC. Fuhren Sie das vollstandige Programm durch.

Nach jedem Gebrauch oder wenn voll
Kaffeesatzbehälter und Tropfschale entleeren

Entleeren und reinigen Sie beide Komponenten, wenn das Warnsymbol blinkt oder die Schwimmer anzeigen, dass sie voll sind. Installieren Sie sie korrekt wieder, um Fehler zu vermeiden.

Nach Verwendung des Dampfs
Dampfduse reinigen und Luftöffnungen freimachen

Fuhren Sie kurzzeitig Dampf in einen Behalter ab, um Milchreste zu spulen. Nehmen Sie die Duse fur eine Grundreinigung mit Burste und Nadel heraus, falls sie verstopft ist.

Wenn mehrere Tage nicht verwendet
Hydraulikkreise spulen

Fuhren Sie eine manuelle Spulung uber das Wartungsmenü durch, um stehendes Wasser aus den Kaffee- und Dampfkreisen vor dem Aufbrühen zu entfernen.

Kostenlose Wartungserinnerungen

Abgestimmt auf Ihr Kaufdatum. Immer kostenlos, jederzeit abbestellbar.

Mit dem Absenden stimmen Sie der Datenschutzerklarung zu. Sie konnen sich in jeder E-Mail mit einem Klick abmelden.
M: qwen/qwen3.8-flash

Stellen Sie eine Frage

0/1000

Empfehlen Sie EA8170 Arabica Display?

Ja Nein

Häufig gestellte Fragen

A

Sie können die Stärke einstellen, indem Sie den Feinheitsknopf im Bohnenbehälter drehen. Nach links drehen macht das Mahl feiner für stärkeren Kaffee, während nach rechts drehen es gröber für milderen Kaffee macht.

Ist diese Antwort hilfreich?

A

Für die besten Ergebnisse verwenden Sie sehr frische, kalte pasteurisierte oder UHT-Milch. Vermeiden Sie Rohmilch, da sie keine optimale Schaumkonsistenz erzeugt.

Ist diese Antwort hilfreich?

A

Die Maschine warnt Sie, wenn eine Reinigung erforderlich ist. Es wird empfohlen, das Reinigungsprogramm monatlich oder whenever die Indikatorlampe blinkt auszuführen, um die Hygiene aufrechtzuerhalten.

Ist diese Antwort hilfreich?

A

Ja, die Maschine hat eine Zwei-Tassen-Funktion, die automatisch zwei vollständige Zubereitungszyklen nacheinander durchführt, um zwei Tassen gleichzeitig zu servieren.

Ist diese Antwort hilfreich?

A

Stellen Sie sicher, dass Sie Ihre Tassen mit heißem Wasser vorwärmen. Sie können auch die Kaffeetemperatur-Einstellung im Wartungsmenü erhöhen, wenn das Standardniveau zu niedrig ist.

Ist diese Antwort hilfreich?

M: QW-35-FL

Vorteile und Nachteile

Vorteile

  • Kompaktes Thermoblock-System sorgt für schnelles Aufheizen und Energieeffizienz
  • 15-Bar-Pumpe liefert authentische Crema bei jedem Schuss
  • Intuitives LCD-Display vereinfacht Navigation und Programmierung
  • Metall-Stufelmahlwerk bietet konsistente Frische für alle Bohnenarten
  • Automatisierte Reinigungs- und Entkalkungszyklen reduzieren manuellen Aufwand
VS

Nachteile

  • Dampfdüse erfordert manuelle Aufschäumtechnik für optimale Textur
  • Wassertankkapazität kann bei intensiver Nutzung häufiges Nachfüllen erfordern
  • Optionales Zubehör wie Auto-Cappuccino-Set separat erhältlich
  • Mahleinstellung muss während des Maschinenlaufs erfolgen für Genauigkeit
  • Entkalkungszyklus erfordert spezifische KRUPS-Produkte für beste Ergebnisse
M: QW-35-FL

Produkt Spezifikation

Leistung

1445,3 W

Farbe

schwarz

Pumpendruck

15 bar

Kaffeesystem

Ganzer Bohnen

Milchsystem

nein

Mahlwerk

einstellbares Kegel Mahlwerk (3 Stufen)

Kaffeemenge

einstellbar

Wassermenge

einstellbar

Kaffee Temperatur

einstellbar (3 Stufen)

Wassertankkapazität

1,7 l

Bohnenbehälterkapazität

0,26 kg

Display

ja

Funktionen

zweihochverstellbarer Auslauf, Automatische Abschaltung, Dampfdüse, Milchaufschäumer (Cappuccinatore), Heißwasserfunktion, integrierter Wasserfilter, automatisches Reinigungsprogramm, automatisches Entkalkungsprogramm

Abmessungen

38,1x48,4x28,7 cm (BxTxH)

Gewicht

7,0 kg

M: QW-35-FL

Produkt Beschreibung

Entdecken Sie die Krups EA 8170 Arabica Display Schwarz Manuelle Erfahrung

Willkommen in der Welt des hausgemachten Brauexzellenz mit der Krups EA 8170 Arabica Display Schwarz. Diese automatische Espressomaschine ist für diejenigen konzipiert, die Kaffeequalität wie im Restaurant verlangen, ohne ihre Küche zu verlassen. Das Gerät verfügt über ein kompaktes Thermoblock-System und eine leistungsstarke 15-Bar-Pumpe, die sicherstellt, dass jeder Ristretto, Espresso oder Kaffee bei perfekter Temperatur mit maximalem Aroma extrahiert wird.

Das benutzerfreundliche LCD-Display führt Sie durch jeden Schritt, von der Zubereitung Ihres Lieblingsgetränks bis zur Durchführung wesentlicher Wartungen. Sie haben volle Kontrolle über Volumen, Intensität und Temperatur, sodass Sie jedes Getränk nach Ihren genauen Vorlieben anpassen können. Ob Sie einen starken Espresso oder einen cremigen Cappuccino mit dem Dampfdüsenrohr wünschen, diese Maschine liefert konsistente Ergebnisse. Der Metallmahlwerk sorgt dafür, dass frische Bohnen direkt vor der Extraktion gemahlen werden, was die reichen Öle und Aromen bewahrt, die eine gute Tasse Kaffee definieren.

Die Wartung ist dank automatisierter Programme zum Spülen, Reinigen und Entkalken unkompliziert. Die Maschine warnt Sie, wenn sie Aufmerksamkeit benötigt, um Langlebigkeit und optimale Leistung zu gewährleisten. Mit seinem schlichten schwarzen Design und der ergonomischen Schnittstelle fügt sich die Krups EA 8170 nahtlos in jede moderne Küche ein und bietet professionelle Funktionalität.

Wichtige Hinweise für Benutzer

  • Heizen Sie Ihre Porzellankannen immer vor, um die beste Espressotemperatur und Crema zu erzielen.
  • Verwenden Sie frisches, kaltes Leitungswasser frei von Chlor für überlegenen Geschmack.
  • Stellen Sie den Mahlgradknopf während des Mahlvorgangs ein für die genauesten Einstellungen.
  • Reinigen Sie die Dampfdüse sofort nach Gebrauch, um Milchrückstände zu vermeiden.
  • Nutzen Sie die optionale Claris Aqua Filterpatrone, um die Lebensdauer der Maschine zu verlängern und den Geschmack zu verbessern.
M: QW-35-FL

© Copyright 2026 Manual.ly